|
|
Power Adders Superchargers, Turbos, Nitrous, etc... |
|
Thread Tools | Display Modes |
07-23-2015, 06:21 PM | #1 |
Registered User
Join Date: Jun 2014
Location: birmingham, alabama
Posts: 11
|
m issfire after nitrous install
I've been trying to figure out what is causing this misfire on cylender 5 i believe. There is a wire that i think the guys that installed my nitrous put in that tins from cylender 5 coil pack and the other side goes into the fire wall where all the other wires for the nitrous enters the firewall. If I hold the wire in a certain position the misfire will go away but always comes back. Any ideas on what this wire is going to? I've already chnged coil packs and spark plugs.
|
07-23-2015, 09:07 PM | #2 |
Registered User
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
|
Re: m issfire after nitrous install
Spark plug gap?
__________________
**SOLD**04' Mach 1 -Comp Cams 106100's (deg 106/110) -Eatonswap with 3.4 Pulley -Full Exhaust (mac lts & xpipe, sss terminator c/b) -Built Rear w/ 3.55 gears [B]-Tuned by Lethal Performance of San Antonio -510hp/478tq |
07-24-2015, 11:38 AM | #3 |
Mach-T
Join Date: Jun 2004
Location: DFW
Posts: 2,865
|
Re: m issfire after nitrous install
take a picture of what you are talking about. Did they use those stupid plastic splicing adapters or solder the wire in? The plastic pieces are quick and easy but they simply suck! I solder all my connections, period.
__________________
Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP |
07-24-2015, 11:46 AM | #4 |
Registered User
Join Date: Apr 2015
Location: Kingsland ga
Posts: 398
|
Re: m issfire after nitrous install
|
07-24-2015, 12:51 PM | #5 |
Registered User
Join Date: Jun 2014
Location: birmingham, alabama
Posts: 11
|
Re: m issfire after nitrous install
Gapped at .35. Heat range 6. There's a wire going into the passenger side coil cover that the people that installed my nitrous put in and it seems to be causing the problem. Any ideas for what this wire is? I'll take a pic when I can. They soldered everything
|
07-24-2015, 01:01 PM | #6 |
Mach-T
Join Date: Jun 2004
Location: DFW
Posts: 2,865
|
Re: m issfire after nitrous install
Do you have a window switch on this kit as well? Some people use this for a tach signal if I recall; I tapped into the tach signal at the PCM.
__________________
Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP |
07-24-2015, 01:50 PM | #7 |
Registered User
Join Date: Jun 2014
Location: birmingham, alabama
Posts: 11
|
Re: m issfire after nitrous install
|
07-26-2015, 08:40 AM | #8 |
Registered User
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
|
Re: m issfire after nitrous install
I had spark blow out with tr6 plugs at 7.5# boost at .035 gap im @ .025 now and its fine.
__________________
mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111 |
08-01-2015, 04:50 PM | #9 | |
Registered User
Join Date: Jun 2014
Location: birmingham, alabama
Posts: 11
|
Re: m issfire after nitrous install
Quote:
i think theres a possibility that the wire that goes to my coil pack for my msd window switch is whats causing my problems. if i move this wire while the car is running the miss will go away but always comes back. i don't really like that they wired it this way anyways because where this wire comes out from under the coil cover it doesn't let it tighten down all the way and I'm sure will let water seep in and mess up my coil packs. i think theres a way to tap the window switch into the ecu. anybody know how to do that? https://www.youtube.com/watch?v=5lGeb-Vovak this is the video of how the misfire sounds Last edited by 03mach1ne; 08-01-2015 at 05:14 PM. |
|
08-03-2015, 04:51 PM | #10 |
Mach-T
Join Date: Jun 2004
Location: DFW
Posts: 2,865
|
Re: m issfire after nitrous install
I have always used pin 26 on the ECU.
__________________
Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|