|
||
|
|
||
|
|||||||
| Mustangs Parts For Sale/Wanted Looking for a Mustang or Part or have one for sale? Post it here! |
 |
|
|
Thread Tools | Display Modes |
10-31-2012, 10:28 PM
|
#1 |
|
Registered User
 Join Date: Sep 2008
Location: Cedar Rapids, Iowa
Posts: 40
|
99% complete eaton swap
SALE PENDING!!!!!!!!!!!!
I have a 99% complete eaton swap for sale. Eaton supercharger 2.8 pulley I have a stock pulley if you want it (21,000 miles on it) Lower intake manifold lower intake intercooler lower intake water adapter with 2 tubes , gasket and bolts Pulley bridge bracket with tensioner and 2 idlers timing cover timing cover tensioner with an idler plus 2 idlers[1 smooth ,1 ribbed idler Lower supercharger pulley with cage and idler Crank harmonic balancer(has a very small chip out of it) Idler bracket with idler - it sits where alternators sit on N/A cars oil cooler with adapter with bolts Alternator upper and lower alternator brackets Alternator pigtail connector Coolant crossover pipe(could use a coat of paint) supercharger inlet plenum with throttle body supercharger pulley cover Bypass valve actuator with 2 bolts IAC valve with bolts and gasket TPS sensor with bolts EGR valve with bolts EGR metal tube Throttle cable Throttle/ cruise cable bracket with bolts Vacuum lines Black bracket with emission sensors , sits on the side of Eaton SC 6rib and 8rib belt 10 supercharger to lower intake bolts 10 supercharger to intercooler bolts Fuel rail set of 8 EV6 39lb injectors Heat exchanger(aftermarket afco unit with brackets welded on to mount on your car) Supercharger reservoir tank intercooling pump intercooling pump pigtail connector Intercooling pump mounting bracket IAT2 sensor ,one on the back of Eaton SC power steering reservoir bracket The lower coolent tube that goes in the vally of the block to clear the intake manifold. Ford gt supercar fuel pump Intake pipe from throttle body to maf Here is all the new from ford gaskets that also come with it. Timing cover gaskets Blower to lower intake gasket Intercooler adapter gasket Plenum and throttle body gasket Iac gasket You will need some ¾ hose for the intercooler system, tune, maf, and intake piping or cold air to finish it off . I think I have all the bolts but you may need a few. 3000 Shipped to you. I will get some pictures tomorrow. Last edited by 99v6red; 11-06-2012 at 05:04 PM. |
|
|
|
10-31-2012, 10:40 PM
|
#2 |
|
AUTOMACHTIC
 
Join Date: Oct 2007
Location: RTP/ N.C.
Posts: 4,813
|
Re: 99% complete eaton swap
Soooooooo Whats up? On 9-15- 2012 it was stated that money was sent and the Eaton swap was sold.
 And then...
__________________
UPGRADES...Tokico Illuminas Borla SS Catback , Steeda Underdrives , Strut Brace , HPM Lower K Brace , L /C Arms , U /C Arms , HPM PanHard Bar, K&N FRPK 2, GOODYEAR GT1 , MRT- H-Pipe , JLT VaporTraps , SLP-12'" Tips! , FRPP Shorty 1 5/8 Headers , Brembo D/S & PBR D/S Rotors ,FRPP Alum.DS ,Roys 3/8 Spacer , SVT Focus 255 pump SCTsw Chip PRO-DYNOjet NA 300.01hp /315tq (Auto) ,Innovate W/B ,Compucar Wet Kit (90jet) + Heater and E Gauge * 360 hp/385tq  12.5 -1/4 @112
|
|
|
|
|
11-01-2012, 12:53 PM
|
#3 |
|
Registered User
Join Date: Sep 2008
Location: Cedar Rapids, Iowa
Posts: 40
|
Re: 99% complete eaton swap
That was a different kit with less then 10k on it. I have a few kits each year!
|
|
|
|
|
11-03-2012, 01:09 PM
|
#4 |
|
Registered User
Join Date: Sep 2008
Location: Cedar Rapids, Iowa
Posts: 40
|
Re: 99% complete eaton swap
bump obo
|
|
|
|
|
11-03-2012, 03:29 PM
|
#5 |
|
Registered User
Join Date: Apr 2010
Location: Cedar Rapids, Ia
Posts: 51
|
Re: 99% complete eaton swap
If I had the money I'd just pick it up from you in townand save ya the shipping. I've wanted this for a while now! Free bump for you.
__________________
2003 DSG Mach 1 JLT CAI Bassani mid length headers Bassani x-pipe Bassani cat-back MGW Orange handle |
|
|
|
|
11-03-2012, 07:11 PM
|
#6 |
|
Registered User
Join Date: Sep 2008
Location: Cedar Rapids, Iowa
Posts: 40
|
Re: 99% complete eaton swap
  
|
|
|
|
|
11-03-2012, 07:26 PM
|
#7 |
|
MECHANIC
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
|
Re: 99% complete eaton swap
i want i want but no scratch right now so free bump great deal really
|
|
|
|
|
11-05-2012, 03:18 AM
|
#8 |
|
Registered User
Join Date: Sep 2008
Location: Cedar Rapids, Iowa
Posts: 40
|
Re: 99% complete eaton swap
2800 shipped my bottom dollar.
|
|
|
|
|
11-05-2012, 11:14 AM
|
#9 |
|
Registered User
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
|
Re: 99% complete eaton swap
Pm sent
__________________
mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111 |
|
|
|
|
11-05-2012, 11:50 AM
|
#10 |
|
Registered User
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
|
Re: 99% complete eaton swap
Pm sent
__________________
mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111 |
|
|
|
|
11-06-2012, 05:05 PM
|
#11 |
|
Registered User
Join Date: Sep 2008
Location: Cedar Rapids, Iowa
Posts: 40
|
Re: 99% complete eaton swap
sale pending!
|
|
|
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
<
Linear Mode
