|
|
Power Adders Superchargers, Turbos, Nitrous, etc... |
|
Thread Tools | Display Modes |
04-18-2014, 09:50 AM | #1 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
Does any know if 2nd Gen. JLT CAI fits....
Like I was saying does anyone know if the second generation JLT intake for our Mach 1 fits the Steeda 2 point shock tower strut brace? Thanks ahead of time guys
|
04-18-2014, 02:45 PM | #2 | |
saving pennies
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
|
Re: Does any know if 2nd Gen. JLT CAI fits....
Quote:
This guy had no problems with the 2 point brace.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels 03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs |
|
04-18-2014, 03:22 PM | #3 | |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
Quote:
Sent from my SCH-I545 using Tapatalk |
|
04-18-2014, 03:24 PM | #4 |
saving pennies
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
|
Re: Does any know if 2nd Gen. JLT CAI fits....
The real question is whether or not it will fit with a intake spacer if you have one.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels 03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs |
04-18-2014, 03:41 PM | #5 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
|
04-18-2014, 03:45 PM | #6 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
|
04-18-2014, 05:16 PM | #7 |
saving pennies
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
|
Re: Does any know if 2nd Gen. JLT CAI fits....
That would mean that the the throttle body is 1/2" higher so the intake pipe will be raised up some.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels 03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs |
04-18-2014, 05:37 PM | #8 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
|
04-18-2014, 07:06 PM | #9 |
Registered User
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
|
Re: Does any know if 2nd Gen. JLT CAI fits....
Looking at the 3rd pic in the set, that looks like MORE than a 1/2" gap he has left over, could be these old eyes, also HE may have a 1/2" spacer as well!! lol, your head hurt yet??
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap: 2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear Tuned by B.Kurgan 601Hp/558/Tq |
04-18-2014, 08:22 PM | #10 | |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
Quote:
Sent from my SCH-I545 using Tapatalk |
|
04-19-2014, 10:49 PM | #11 |
Registered User
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
|
I have a 1/2" spacer, JLT intake, and 2-point strut brace on my daily driven Mach. No issues.
__________________
03 Mach (Auto) JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only) |
04-19-2014, 11:00 PM | #12 | |
saving pennies
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
|
Quote:
Sent from my XT1080 using Tapatalk
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels 03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs |
|
04-19-2014, 11:07 PM | #13 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
|
04-22-2014, 11:43 AM | #14 |
Registered User
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
|
I have no idea. When was the changeover?
__________________
03 Mach (Auto) JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only) |
04-22-2014, 01:26 PM | #15 |
saving pennies
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
|
Re: Does any know if 2nd Gen. JLT CAI fits....
Gen 1
Gen 2 Prob about 2 years ago. You can see the difference in the shield around the filter and the shape of the pipe.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels 03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs |
04-22-2014, 07:47 PM | #16 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
2nd generation intake tube looks not as wide and shorter than 1st, and looks like a longer filter. Remember that the 1st would hit the inside of hood. And now 2nd from what I read above clears Steed 2 point shock tower strut.
Sent from my SCH-I545 using Tapatalk |
04-23-2014, 10:56 AM | #17 |
Registered User
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
|
Based on those pics, I have a Gen. 1. It clears my 2-pt brace, but it does rub the hood.
__________________
03 Mach (Auto) JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only) |
04-23-2014, 11:05 AM | #18 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
|
04-24-2014, 01:48 AM | #19 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
|
06-02-2014, 01:37 AM | #20 |
Registered User
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
|
Re: Does any know if 2nd Gen. JLT CAI fits....
Wanted to update you guys that helped. It fits but tight fit with a bit of clearance issue but nothing serious.
|
06-02-2014, 11:17 AM | #21 |
Registered User
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
|
Re: Does any know if 2nd Gen. JLT CAI fits....
Glad you got it,
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap: 2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear Tuned by B.Kurgan 601Hp/558/Tq |
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|