|
12-07-2004, 04:14 PM | #1 |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
How to change your 5 speed to an automatic
Here is it, in plain english when possible.
Think this about everything, minus the tranny and converter. I will add as I remember. This will acheive a stock looking automatic Mach 1: 1R3Z-7210-AA - Shifter assembly: $174.42 XR3Z-7E395-AA - Trans shift cable assy: $48.24 F6SZ-7007-A - Lower bellhousing cover: $32.47 XR32-7C078-BA - 4R70W wiring harness: $90.00 XR3Z-7B229-AA - Brkt-trans kickdown cable: $9.80 3R3Z-6304567-AAB - Bezel out of Mach 1, I traded for charcoal gray: $170.22 1R3Z-4841-EA - 4R70W driveshaft yoke for tranny tailshaft: $85.38 F1VY-7986-A - ***-Will post desciption up later: $5.70 F8AZ-7G276-AA - Shifter position sensor: $22.27 F6ZZ-3F719-AC - Cable asy-ign shift interlock: $57.18 E43Z-7B415-A - Stud-tr gr sh conn rod adj: $6.18 F1DZ-7H181-A - Fitting-trans shft actu ca: $7.68 1L3Z-7H103-AB - Speed sensor: $22.31 XR3Z-7A228-BA - Fill tube for tranny fluid: $15.83 XR3Z-7A020-BA - Dip stick for fill tube: $19.37 378377-S - Plug button for firewall hole 1.38 dia: $1.91 F2UZ-7H183-A - Plug for the mechanical speed sensor - if not supplied with transmission Also need: -8 bolt flexplate. I got mine from Perfomance Automatic for $226.00 -Plug for convertor/flexplate access port on bottom of bellhousing, Ford $4.00 -GT automatic brake pedal, Ford $30.00 -Mach 1 brake pedal cover, Ford $32.00 -B&M 24,000 GVW tranny cooler, Summit $48.00 -Tranny cooler lines and fittings, Auto Zone $40.00 -Switch for overdrive to replace coin holder, Strictly Pro $10.00 -1350 to 1330 u-joint for tailshaft yoke, Auto Zone $30.00 -11/16 driveshaft spacer from Steeda, $20.00 Questions: Steve (314) 409-6731
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg |
12-07-2004, 04:17 PM | #2 |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
The wiring harness is 03 Cobra specific. I would double check
the 3650 harness. I am almost sure they are very close in design though. Enjoy.
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg |
12-07-2004, 04:35 PM | #3 |
Lakers beat our butts
Join Date: Jan 2004
Location: San Antonio TX
Posts: 2,889
|
If you wanted an auto why did you buy a 5 spd???
__________________
SPURS ARE NBA 07 CHAMPS!!!,but we wont be in 08 04 Oxford White 5 Spd with IUP K&N Aircharger Borla Stingers SLP Catted X Steeda Tri-Ax SCT flash tune. Drilled/Slotted rotors all 4 corners. 283rwhp (Mustang Dyno) 306rwhp (sae on Dynojet) D/O/B 12-05-03 Del. 01-21-04 |
12-07-2004, 04:41 PM | #4 |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
He he...check my sig.
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg |
12-07-2004, 04:51 PM | #5 | |
it's soo-tack
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,082
|
Quote:
I didn't think they were a direct swap for the 96+? I guess your ABS is long gone?
__________________
mark 2004 DSG Mach 1. Built motor. Turbo. 667whp 2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold) 2003 DSG Mach 1. 12.65 @ 106 (sold) |
|
12-07-2004, 05:24 PM | #6 | |
Registered User
Join Date: Jun 2004
Location: Madera, CA
Posts: 7,687
|
Quote:
Um, ok, I dont' see the answer, am I blind? The question still stands for me. even with a 10 sec. car, if you are going with an auto, it wuldn't be stock anywho.... |
|
12-07-2004, 05:51 PM | #7 |
Registered User
Join Date: Sep 2004
Location: Atlanta, GA
Posts: 24
|
He put an automatic in his cobra, which only come in manual.
|
12-07-2004, 05:54 PM | #8 | |
Registered User
Join Date: Jun 2004
Location: Madera, CA
Posts: 7,687
|
Quote:
Since when? |
|
12-07-2004, 05:58 PM | #9 |
Registered User
Join Date: Sep 2004
Location: Atlanta, GA
Posts: 24
|
I will be happy to admit if I am wrong, but I believe since 1993...
|
12-07-2004, 06:42 PM | #10 |
Registered User
Join Date: Nov 2004
Location: Bloomington, IL
Posts: 173
|
I believe SVT has never produced an Automatic Cobra. I can't be positive for years 94/95, but I am pretty sure. I am however, prositive that they have not produced one from 96 and up. No auto 4.6 4V Cobra
__________________
'03 Torch Red Mach 1 5-speed, IUP Bassani Catback 17x9 17x10.5 Chrome Bullitts |
12-07-2004, 07:38 PM | #11 | |
Gone but not forgotten
Join Date: Oct 2002
Location: Illinois
Posts: 524
|
Quote:
__________________
Dave 03 Mach 1 VIN# 349977 White Auto with IUP Built 11/22/02 Sold 9/1/07 |
|
12-07-2004, 08:44 PM | #12 |
Registered User
Join Date: Oct 2004
Posts: 51
|
So steve?
So steve how much did it cost you total to turn ur stick into an auto? How do you like it, what kinda tranny u got in it, let me know
|
12-07-2004, 08:55 PM | #13 |
Registered User
Join Date: Apr 2004
Location: Allen Park, Michigan
Posts: 533
|
Funny this came up. I was wondering how hard it would be to do this to a 97 cobra convertible. Total $? What about labor?
Switch for overdrive to replace coin holder? The OD switch should be on the side of the shift handle.
__________________
04 Screeming Yellow Auto: Best 1/4 mile time basically stock with auto transmission = 13.45 @ 104.14/ Best 0-60 MPH = 5.0 seconds Stock Mach 1, only 7000 miles, K&N air filter, Yellow top Optima battery, Viper 791xv 2-way interactive alarm with remote start and nite-lite autolamp system, Ford automatic dimming rearview mirror with outside temp and compass display. Last edited by jonkolo; 12-07-2004 at 09:09 PM. |
12-07-2004, 09:01 PM | #14 | |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
Quote:
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg |
|
12-07-2004, 09:03 PM | #15 | |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
Quote:
Honestly though, if I had to do it all over, I would not bother with the ABS stuff. It's a foo foo feature that just costs extra money to make work. And the **** ring gets in the way if a stud gets spinned in the axle.
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg Last edited by 03Steve; 12-07-2004 at 09:07 PM. |
|
12-07-2004, 09:15 PM | #16 |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
Add all of the parts above, along with:
-Lentech Strip Terminator 4R70W ($2595) -9.5" 3200 non-locking converter ($595) -35 spline input shaft and stage 2 drum ($399) -Shipping ($175) I sold the T-56 for about $2000, and some other goodies that were associated with the manual tranny. That helped with the cost. Labor is a good weekend. Like any "larger than bolt on" job, the most difficult part is having all the right parts on hand, and having someone around to go on a part run. Getting all the parts on hand is key, that shortens labor. That is why I created this write-up and posted this up. To save time and aggrevation for anyone who chooses to do this.
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg |
12-08-2004, 05:12 PM | #17 |
Registered User
Join Date: Jun 2004
Location: Madera, CA
Posts: 7,687
|
no autos in cobras? really......Can you tell I dont' know THAT much about them...duh.
Now why did they offer the mach with an auto, but not a cobra? I could have sworn I have seen listings on dealers websites with cobras having an auto......ok that is it I am going crazy...... It is especially wierd because there is a girl that has an 04 cobra, brand new no plates, around here and I could have sworn it was an auto.....tall tale signs....smooth shift, no delay between gears, breaking until light turns green.....man am I lost....no offense to the women that come here, but this girl looks like she can barely drive an SUV....you'd have to see her. |
12-08-2004, 06:05 PM | #18 | |
Lakers beat our butts
Join Date: Jan 2004
Location: San Antonio TX
Posts: 2,889
|
Quote:
I see now. My nephew did the same with his 03 snake no more 6spd or IRS although he used a MACH rear and Stock Tranny
__________________
SPURS ARE NBA 07 CHAMPS!!!,but we wont be in 08 04 Oxford White 5 Spd with IUP K&N Aircharger Borla Stingers SLP Catted X Steeda Tri-Ax SCT flash tune. Drilled/Slotted rotors all 4 corners. 283rwhp (Mustang Dyno) 306rwhp (sae on Dynojet) D/O/B 12-05-03 Del. 01-21-04 |
|
12-08-2004, 06:15 PM | #19 | |
Mach-O-Haulic
Join Date: Sep 2002
Location: Washington, MO
Posts: 981
|
Quote:
There are a couple of women that I know who can shift smoother than what I do normally. So the girl could know how to handle a stick, or she/her parents have to much money and had it converted for her to ba able to drive.
__________________
Mach #12003 Mach 1 Torch Red IUP 5-speed Mach #22004 Mach 1 Comp. Orange IUP 5-speed Engine Parts 4 Sale |
|
12-08-2004, 07:44 PM | #20 |
Slow Mach 1
Join Date: Feb 2003
Location: Miami, Fl
Posts: 1,288
|
I'm pretty sure I have seen a 4V auto before. Last year would have been 98.
|
12-08-2004, 08:03 PM | #21 | |
Registered User
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
|
Quote:
__________________
2003 Cobra Coupe SOLD WFC8 #7 Heads Up Qualifier - Cobra Eliminator MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle Saleen Clone CURRENT -10.7:1 Compression and 2.3L Whipple -Comp Cams 106360 cams @ 108LSA -4R70W and CVAF1 Auto EEC -96 Cobra Rear End -Machine/Head work by Todd Fays of Phase 2 Crestwood, MO http://i79.photobucket.com/albums/j1...unch2small.jpg |
|
12-08-2004, 08:36 PM | #22 |
OG Mach1Misfit
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
|
There is no such thing as a Factory auto cobra period.
No arguments, no speeches. They never made one. I did do some minor assisting in Steve's deal though. So there are a handful of conversions. When you have a car like Steve's..you couldn't shift fast enough... |
12-08-2004, 08:55 PM | #23 |
Slow Mach 1
Join Date: Feb 2003
Location: Miami, Fl
Posts: 1,288
|
Maybe you guys are right. I could have sworn I saw a 97 or 98 black conv't with an auto.
|
12-08-2004, 10:25 PM | #24 | |
Registered User
Join Date: Apr 2004
Location: Golden Beach, MD
Posts: 86
|
Quote:
__________________
2004 IUP Auto " Max " Build Date: 2/17/04 Borla Stingers 4.10's Superchip Performance Tune MGW MACh 1 Shift Knob K&N Aircharger |
|
12-08-2004, 11:30 PM | #25 | |
Registered User
Join Date: Mar 2003
Location: Orlando, FL
Posts: 748
|
Quote:
jc
__________________
'06 Black Trailblazer SS; 13.6 @ 101 '98 Black SVT Contour #4115 Gone but not forgotten: '03 Black Mach 1 A4 (13.7 @ 104); '03 Torch Red Mach 1 M5 (13.4 @ 106), '01 White SVT Lightning (13.4 @ 103), '78 Silver Z28, '95 Lincoln Mark VIII, 3 T-birds |
|
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|