|
03-13-2008, 02:53 PM | #51 |
Registered User
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
|
Re: Header install guide?
as one other person asked, does anyone know which headers will fit on autos?
also, i'm curious, what's the difference in flow between LTs and which ever (shorties or mids) are the same length as stock? (i either want LTs or stock length as my exhaust is currently set up to take either, but i don't wanna buy more piping to make the other setup work)
__________________
03 Mach (Auto) JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only) |
10-25-2009, 04:10 PM | #52 | |
Registered User
Join Date: Sep 2008
Location: Charleston,WV
Posts: 263
|
Re: Header install guide?
Quote:
__________________
No more toys right now looking for some more... |
|
10-25-2009, 04:30 PM | #53 |
Mach1 member
Join Date: Aug 2003
Location: East Haven, CT
Posts: 3,349
|
Re: Header install guide?
Your quoting someone from over four years ago. Get a clue.
__________________
2011 Mustang GT Grabber Blue Automatic 2003 Mach 1 Whipple 2.3 718 rwhp 735 rwtq @25 psi SOLD |
12-20-2009, 09:12 AM | #54 |
Registered User
Join Date: Dec 2009
Location: Chesapeake, VA
Posts: 1
|
Re: Header install guide?
I just finished installing my Kooks L/T headers and UPR K member kit. I have not had time to dyno her yet but I did feel a bunch more power already. My first dyno tune was 2 years ago with all the other mods in my sig minus the Headers and I put down 318.8RWHP and 335RWTQ with the knock sensors off....I can't wait for this new tune...
__________________
NEW DYNO TUNE NUMBERS TO COME AFTER THE NEW YEAR:rockon:JLT cai, Steeda udp, Kooks longtube headers and catted X-pipe , JBA 3inch Catback, MGW Orange Handle, Custom 2.5 inch SFC's, 03/04 Cobra Clutch kit, Fidanza Aluminum Flywheel, Custom SCTxcal3 tune by Brent @ DTP, 4.10 gears w/rebuilt diff. w/1 xtra clutch pack. UPR K-member kit/A-arms/12-350 Coilovers, Koni Adjustable Sport Struts, MM CC Plates and UPR- Bumpsteer. bumpsteer. FOR SALE: MAGNAFLOW TRU CATTED X PIPE-$300+SHIPPING.... |
05-29-2010, 11:37 PM | #55 |
Registered User
Join Date: May 2010
Location: Ohio
Posts: 378
|
Re: Header install guide?
Just figured id share my personal info from the header install on my car. I used AmericanMuscle.com for instructions, and was satisfied, but not impressed. You dont need to unbolt the AC pump as they said, and they wanted you to jack the motor from the oil pan, which works, untill you put a nice dent in it Their illistrations are not accurate for how high the car needs to be. I had mine with the front tires about 4 or 5 inches off the ground, NOT ENOUGH. Dropping the K member was a ***** because the car was so low, and it was hard to get it out with the steering rack hanging from the sway bar as they said to do it. Also, the oil dipstick in my case, would NOT come out. I eneded up using vice grips and a massive dent in the dip stick to get it out. And finally, the socket sizes were not all exact, I think I found 1-2 incorrect sizes, which could lead to stripped bolt heads. I ended up beeing cheap, I used the factory studs and nuts again, but one had to be shortened. I also used NEW stock Ford gaskets. Im glad it was a sorce though, and the illistrations right or wrong were very helpfull. Without several road blocks not due to the instructions, it took me on my own around 20 hours. Of course I needed a second hand on the K member drop and install. The biggest pain was one of the top passenger side header bolts.
Im glad I did it, it was not too hard, but time consuming. It sounds great and was well worth it.
__________________
Ben - 04 Mach 1 -Mac LT, LP o/r x, Mangaflow cb, K&N CAI, MMR 1/2" spacer, Custom cams, degreed ftw 356/339 12.04 @ 113.9 -Is it bench racing if the car hasnt ran in a year? |
06-01-2010, 03:43 AM | #56 |
Book'em Danno!
Join Date: Jun 2007
Location: Ewa Beach, HI
Posts: 454
|
Re: Header install guide?
Old thread but want to know if Kooks LT will fit with an auto trans Mach!
Or American Racing is choice B. Any thoughts or comments appreciated.
__________________
MAC ss catback Pypes O/R X Roy's 3/8" spacer C&L intake system 4.10's MM springs Bilstein HD's MM cc plates SCT X3 Slotted/Drilled rotors Hawk HPS pads. AFS '03 Cobra replicas 18x9 & 18x10.5 Nitto Invo 275/35/18 & 295/35/18 Cobra folding mirrors & other Cobra exterior parts AM smoked headlight & fogs. HID 8k headlight and fogs Future Mods: LT headers, MM flsfc, panhard, Torque converter, and more Cobra body parts . |
06-01-2010, 04:26 AM | #57 | |
Soldier for Christ
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
|
Re: Header install guide?
Quote:
here is some different set ups with kooks, i was looking threw there and it didn't have anything different from auto to 5 speed so i don't know for sure. might want to call them or kooks to ask. i'm sure someone on here will know for sure
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh |
|
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|