|
01-04-2010, 09:07 PM | #201 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: Ford Racing Cams Installed - WOW!!!!!
So it was tuned with SCT software on a dynojet dyno? If so, those numbers are extremely low. 340 would be more like it.
|
01-04-2010, 09:59 PM | #202 |
Registered User
Join Date: Nov 2005
Location: Kathleen, GA
Posts: 261
|
Re: Ford Racing Cams Installed - WOW!!!!!
So you think there is about 20hp left in it? What about the torque? Does that look about right? It was conservative tune for a street car not a track brawler as it has never seen a track. I doubt it matters much but it has heavy @ss 18inch rims and 315 tires. The stock wheel tire combo is obviously lighter on the car as I usually switch to the stockers for the winter and it feels a ton faster.
__________________
Suspension Mods: Steeda Strut Tower brace - Steeda Front swaybar - Bilstein HD struts/shocks - MM Caster/Camber plates - MM RLCAs - MM FLSFCs - MM PHB - MM front coil-overs - MM Torque Arm - MM Rear TA springs Other: FRPP 4.10 gears - TA Diff cover - FR500 Cams - Accufab Throttle body - JBA midlength headers - Matching catted H-pipe - Borla stinger catback - 320rwhp/320tq Fuel mileage: 25city/28hwy |
01-04-2010, 10:02 PM | #203 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: Ford Racing Cams Installed - WOW!!!!!
There is defintely more power to be had. Were the cams degreed? A Mach engine with 96-98 intake cams is in the 340rwhp range and your FR cams have more duration and lift. A bone stock bolt on engine can make as much as yours is putting down.
|
01-05-2010, 12:49 PM | #204 |
Procharger = Very Fun
Join Date: Oct 2003
Location: Simi Valley, CA
Posts: 877
|
Re: Ford Racing Cams Installed - WOW!!!!!
There is no mention of a cold-air intake. Maybe some restrictions there, perhaps?
|
01-05-2010, 12:52 PM | #205 |
Shitin 'n Gitin
Join Date: Mar 2007
Location: Pasadena, MD
Posts: 1,416
|
Re: Ford Racing Cams Installed - WOW!!!!!
I would ask your builder what he degreed the cams at... Mine were installed at 109 centerline like were recommended and you see where my power is at.
__________________
2003 AB Mach -- 442/435 @ the rear ALL MOTOR -Race Gas FRPP BOSS 5.0 block, 10.6:1 compression, Manley H-Beams; Diamond flat-top pistons, P&P heads W/ 5-angle valve job & ARP Head studs, PP upper/lower intake, Comp Stage 2 N/A cams, FR500 springs, valves, and followers, Tube K with coilovers and Bilsteins, Kooks, Stingers, 2.97 T-56 Magnum, 31 Spline Superior axles & Auburn-pro dif, built battle boxes, KB BAP w/ 39lb injectors, and 4:10's. |
01-05-2010, 01:00 PM | #206 |
Registered User
Join Date: Nov 2005
Location: Kathleen, GA
Posts: 261
|
Re: Ford Racing Cams Installed - WOW!!!!!
I will check into the degree question and yes no CAI due to steeda strut tower brace, only a drop in K&N. I think he dynoed it with a stock gear setting also since he had to change it to my actual 410 while I was picking it up after the tune. Would that or the heavy 18" rims/tires be a factor to the numbers at all? There is a huge difference when I switch to the stock wheels/tires at least in SOP feel.
__________________
Suspension Mods: Steeda Strut Tower brace - Steeda Front swaybar - Bilstein HD struts/shocks - MM Caster/Camber plates - MM RLCAs - MM FLSFCs - MM PHB - MM front coil-overs - MM Torque Arm - MM Rear TA springs Other: FRPP 4.10 gears - TA Diff cover - FR500 Cams - Accufab Throttle body - JBA midlength headers - Matching catted H-pipe - Borla stinger catback - 320rwhp/320tq Fuel mileage: 25city/28hwy |
01-05-2010, 01:08 PM | #207 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: Ford Racing Cams Installed - WOW!!!!!
|
01-05-2010, 01:20 PM | #208 | |
Shitin 'n Gitin
Join Date: Mar 2007
Location: Pasadena, MD
Posts: 1,416
|
Re: Ford Racing Cams Installed - WOW!!!!!
Quote:
I agree though, with my cobra r 17X10.5's with mickey thompsons on there it feels faster too, but thats mainly becuase I'm actually getting traction haha
__________________
2003 AB Mach -- 442/435 @ the rear ALL MOTOR -Race Gas FRPP BOSS 5.0 block, 10.6:1 compression, Manley H-Beams; Diamond flat-top pistons, P&P heads W/ 5-angle valve job & ARP Head studs, PP upper/lower intake, Comp Stage 2 N/A cams, FR500 springs, valves, and followers, Tube K with coilovers and Bilsteins, Kooks, Stingers, 2.97 T-56 Magnum, 31 Spline Superior axles & Auburn-pro dif, built battle boxes, KB BAP w/ 39lb injectors, and 4:10's. |
|
01-05-2010, 03:42 PM | #209 |
Registered User
Join Date: Aug 2003
Location: Simi Valley, CA
Posts: 1,383
|
Re: Ford Racing Cams Installed - WOW!!!!!
Yes, the car with heavier 18in rims will dyno lower than with lighter rims.
Jerome
__________________
03 Mach1 5spd BB/Stroker built by Eddie Rios Addiction Motorsports P&P 03 Heads by Al P Custom cams by NASVT Nazty PSR SAE 420rwhp SAE 387rwt 1.56 60ft 11.44ET 122.1mph 1700 DA |
01-14-2010, 07:47 PM | #210 |
Registered User
Join Date: Nov 2005
Location: Kathleen, GA
Posts: 261
|
Re: Ford Racing Cams Installed - WOW!!!!!
The cams were set up according to specs. A little bit of an excuse but the tuner said their dyno always shows lower numbers than most. I will get it retuned with the next mod. Yet another excuse to do something else to the car.
__________________
Suspension Mods: Steeda Strut Tower brace - Steeda Front swaybar - Bilstein HD struts/shocks - MM Caster/Camber plates - MM RLCAs - MM FLSFCs - MM PHB - MM front coil-overs - MM Torque Arm - MM Rear TA springs Other: FRPP 4.10 gears - TA Diff cover - FR500 Cams - Accufab Throttle body - JBA midlength headers - Matching catted H-pipe - Borla stinger catback - 320rwhp/320tq Fuel mileage: 25city/28hwy |
01-30-2010, 04:37 PM | #211 |
Registered User
Join Date: Nov 2005
Location: Kathleen, GA
Posts: 261
|
Re: Ford Racing Cams Installed - WOW!!!!!
Been a while but here was the dyno sheet from the tune. Maybe it will give some insight.
__________________
Suspension Mods: Steeda Strut Tower brace - Steeda Front swaybar - Bilstein HD struts/shocks - MM Caster/Camber plates - MM RLCAs - MM FLSFCs - MM PHB - MM front coil-overs - MM Torque Arm - MM Rear TA springs Other: FRPP 4.10 gears - TA Diff cover - FR500 Cams - Accufab Throttle body - JBA midlength headers - Matching catted H-pipe - Borla stinger catback - 320rwhp/320tq Fuel mileage: 25city/28hwy |
04-03-2010, 11:51 AM | #212 |
Registered User
Join Date: Jan 2010
Location: York, PA
Posts: 121
|
Re: Ford Racing Cams Installed - WOW!!!!!
I know this is old but im thinking about these for my daily driver with mods in my sig and wondering how it is just cruising around? Also how much did it cost you for install and tune if you dont mind me asking because CJ Pony Parts has the kit for 850 bucks thats complete with cams, vavles, springs, valve seals and followers
__________________
Past: 2004 Competition Orange Mach 1 M5 SOLD 7/12/11 4.10 gears K&N intake SLP x pipe Borla Stingers MGW shifter Current: 2006 F150 FX4 Black supercab 6.5' bed all stock and hoping to resist mods |
04-03-2010, 04:35 PM | #213 |
Registered User
Join Date: Aug 2003
Location: Simi Valley, CA
Posts: 1,383
|
Re: Ford Racing Cams Installed - WOW!!!!!
I ran these cams for about 30K miles in my daily driver. Their drivability is just like stock cams. They have a mild lopw at idle.
Jerome
__________________
03 Mach1 5spd BB/Stroker built by Eddie Rios Addiction Motorsports P&P 03 Heads by Al P Custom cams by NASVT Nazty PSR SAE 420rwhp SAE 387rwt 1.56 60ft 11.44ET 122.1mph 1700 DA |
04-06-2010, 01:50 AM | #214 | |
Super Moderator
Join Date: Sep 2003
Location: Houston (Crosby), Texas
Posts: 6,689
|
Re: Ford Racing Cams Installed - WOW!!!!!
Quote:
What MAF are you running?
__________________
2003 Dark Shadow Gray Mach 1 5.3L Stroker - FR500 Intake - Boss330 Heads 4.56 Gears - Kooks LTs - SCT Tune - Bassani X/Catback 2004 Silver Metallic Cobra 2.3 Whipple - 60lb injectors -Twin FGT Pumps 8 gauge/BAP/FPDM - JLT - Bassani Catted X / Catback - SCT PRP - 4# Lower - 3.50/3.00 Uppers - 19/24 PSI 2017 White Shelby F150 2.9L Whipple _______________ |
|
04-06-2010, 09:00 AM | #215 | |
Registered User
Join Date: Sep 2005
Location: omaha NE
Posts: 804
|
Re: Ford Racing Cams Installed - WOW!!!!!
Quote:
__________________
'86 Scirocco 16v '03 20AE '03 Mach 1 Azure Blue ...went IRS...never looked back... Born: 03/26/2003 Bought: 09/07/2005 |
|
04-06-2010, 09:08 AM | #216 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: Ford Racing Cams Installed - WOW!!!!!
|
04-06-2010, 09:13 AM | #217 |
Registered User
Join Date: Jan 2010
Location: York, PA
Posts: 121
|
Re: Ford Racing Cams Installed - WOW!!!!!
I found them in CJ Pony Parts catalog. I looked for them on their website but couldnt find them for some reason but called them and gave them the part number and they have some in stock. They are a top 10 dealer for ford racing parts
__________________
Past: 2004 Competition Orange Mach 1 M5 SOLD 7/12/11 4.10 gears K&N intake SLP x pipe Borla Stingers MGW shifter Current: 2006 F150 FX4 Black supercab 6.5' bed all stock and hoping to resist mods |
04-06-2010, 09:36 AM | #218 |
Registered User
Join Date: Sep 2005
Location: omaha NE
Posts: 804
|
Re: Ford Racing Cams Installed - WOW!!!!!
ahh...thanks, i'll call them.
I didn't know the price had droped so much.
__________________
'86 Scirocco 16v '03 20AE '03 Mach 1 Azure Blue ...went IRS...never looked back... Born: 03/26/2003 Bought: 09/07/2005 |
04-06-2010, 09:50 AM | #219 |
Shitin 'n Gitin
Join Date: Mar 2007
Location: Pasadena, MD
Posts: 1,416
|
Re: Ford Racing Cams Installed - WOW!!!!!
I wouldn't call my car a daily driver much anymore, but I used to daily drive it with the cams, never had any issues. Drove it for probably 20K miles with the cams in so far. Drove it up to carlisle and down to Myrtle beach with them and it acts like a stock mach until you get into the go pedal. I would also follow his advise and just get some custom grinds, I mean they make great power (look at my sig) but with more duration they will have a much meaner idle which mine lacks.
__________________
2003 AB Mach -- 442/435 @ the rear ALL MOTOR -Race Gas FRPP BOSS 5.0 block, 10.6:1 compression, Manley H-Beams; Diamond flat-top pistons, P&P heads W/ 5-angle valve job & ARP Head studs, PP upper/lower intake, Comp Stage 2 N/A cams, FR500 springs, valves, and followers, Tube K with coilovers and Bilsteins, Kooks, Stingers, 2.97 T-56 Magnum, 31 Spline Superior axles & Auburn-pro dif, built battle boxes, KB BAP w/ 39lb injectors, and 4:10's. |
04-06-2010, 11:31 AM | #220 | |
Registered User
Join Date: Feb 2008
Location: Sacramento, Ca
Posts: 1,044
|
Re: Ford Racing Cams Installed - WOW!!!!!
Quote:
__________________
2003 Mach 1 5spd Black with IUP Engine Mods: cone filter, Crower stage 2 cams, Hooker long tubes, SLP Powerflo exhaust Rear end: Cobra diff, moser axles, 3.73 gears, Ford Racing aluminum driveshaft Suspension: Eibach Pro kit with poly isolators And some other small things... 348.6/331.6 sae |
|
04-06-2010, 03:29 PM | #221 | |||
Registered User
Join Date: Aug 2003
Location: Simi Valley, CA
Posts: 1,383
|
Re: Ford Racing Cams Installed - WOW!!!!!
Quote:
Quote:
Quote:
Jerome
__________________
03 Mach1 5spd BB/Stroker built by Eddie Rios Addiction Motorsports P&P 03 Heads by Al P Custom cams by NASVT Nazty PSR SAE 420rwhp SAE 387rwt 1.56 60ft 11.44ET 122.1mph 1700 DA |
|||
07-05-2012, 08:07 PM | #222 |
Registered User
Join Date: Jan 2012
Location: Nocturnal Wonderland
Posts: 351
|
Re: Ford Racing Cams Installed - WOW!!!!!
where can you purchase the FR500 cams and valvetrain?
__________________
2003 OW mach1...under construction. |
07-05-2012, 08:08 PM | #223 |
Registered User
Join Date: Jan 2012
Location: Nocturnal Wonderland
Posts: 351
|
Re: Ford Racing Cams Installed - WOW!!!!!
hey N/A you make custom grind cams or you just do the specs?
__________________
2003 OW mach1...under construction. |
07-05-2012, 09:12 PM | #224 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: Ford Racing Cams Installed - WOW!!!!!
Fr500 cam kits are no longer available. I bought the last of the kits a few years ago.
__________________
https://www.facebook.com/groups/481330828691064/ |
07-11-2014, 11:31 AM | #225 |
Registered User
Join Date: Apr 2014
Location: Virginia Beach, VA
Posts: 49
|
Re: Ford Racing Cams Installed - WOW!!!!!
Id love to get cams for my 04 Mach, but i am not that savvy on doing it myself. guess the question would be if I were to go with Comp camps, how much would it cost to install? seeing that springs and valves for that kit were not good on stock heads. not all cams are that way when you purchase them are they?
__________________
[FONT="Comic Sans MS"]2002 STEEDA Mustang - RIP 2004 Competition Orange MACH1 - Purchased 4-24-14 - Arrival (5-2-14) |
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|