2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 04-18-2014, 09:50 AM   #1
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Does any know if 2nd Gen. JLT CAI fits....

Like I was saying does anyone know if the second generation JLT intake for our Mach 1 fits the Steeda 2 point shock tower strut brace? Thanks ahead of time guys
frijol79 is offline   Reply With Quote
Old 04-18-2014, 02:45 PM   #2
Mustang9668
saving pennies
 
Mustang9668's Avatar
 
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
Re: Does any know if 2nd Gen. JLT CAI fits....

Quote:
Originally Posted by frijol79 View Post
Like I was saying does anyone know if the second generation JLT intake for our Mach 1 fits the Steeda 2 point shock tower strut brace? Thanks ahead of time guys
http://www.moddedmustangs.com/forums...ml#post5358071

This guy had no problems with the 2 point brace.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels

03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs
Mustang9668 is offline   Reply With Quote
Old 04-18-2014, 03:22 PM   #3
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by Mustang9668 View Post
http://www.moddedmustangs.com/forums...ml#post5358071

This guy had no problems with the 2 point brace.
Thank you very much

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-18-2014, 03:24 PM   #4
Mustang9668
saving pennies
 
Mustang9668's Avatar
 
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
Re: Does any know if 2nd Gen. JLT CAI fits....

Quote:
Originally Posted by frijol79 View Post
Thank you very much

Sent from my SCH-I545 using Tapatalk
The real question is whether or not it will fit with a intake spacer if you have one.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels

03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs
Mustang9668 is offline   Reply With Quote
Old 04-18-2014, 03:41 PM   #5
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by Mustang9668 View Post
The real question is whether or not it will fit with a intake spacer if you have one.
I do have 1/2 in spacer

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-18-2014, 03:45 PM   #6
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by Mustang9668 View Post
The real question is whether or not it will fit with a intake spacer if you have one.
What would be the problem?

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-18-2014, 05:16 PM   #7
Mustang9668
saving pennies
 
Mustang9668's Avatar
 
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
Re: Does any know if 2nd Gen. JLT CAI fits....

That would mean that the the throttle body is 1/2" higher so the intake pipe will be raised up some.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels

03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs
Mustang9668 is offline   Reply With Quote
Old 04-18-2014, 05:37 PM   #8
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by Mustang9668 View Post
That would mean that the the throttle body is 1/2" higher so the intake pipe will be raised up some.
I hear you, might need to Find out.

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-18-2014, 07:06 PM   #9
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Does any know if 2nd Gen. JLT CAI fits....

Looking at the 3rd pic in the set, that looks like MORE than a 1/2" gap he has left over, could be these old eyes, also HE may have a 1/2" spacer as well!! lol, your head hurt yet??
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 04-18-2014, 08:22 PM   #10
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by not a gt View Post
Looking at the 3rd pic in the set, that looks like MORE than a 1/2" gap he has left over, could be these old eyes, also HE may have a 1/2" spacer as well!! lol, your head hurt yet??
Yeah i see that too but the outside of intake tube towards the fender looks like it's to close to the brace.

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-19-2014, 10:49 PM   #11
mach1metalhead
Registered User
 
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
I have a 1/2" spacer, JLT intake, and 2-point strut brace on my daily driven Mach. No issues.
__________________
03 Mach (Auto)
JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only)
mach1metalhead is offline   Reply With Quote
Old 04-19-2014, 11:00 PM   #12
Mustang9668
saving pennies
 
Mustang9668's Avatar
 
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
Quote:
Originally Posted by mach1metalhead View Post
I have a 1/2" spacer, JLT intake, and 2-point strut brace on my daily driven Mach. No issues.
Do you have the gen 1 or gen 2 JLT?

Sent from my XT1080 using Tapatalk
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels

03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs
Mustang9668 is offline   Reply With Quote
Old 04-19-2014, 11:07 PM   #13
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by Mustang9668 View Post
Do you have the gen 1 or gen 2 JLT?

Sent from my XT1080 using Tapatalk
I believe it's 2nd Gen.

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-22-2014, 11:43 AM   #14
mach1metalhead
Registered User
 
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
Quote:
Originally Posted by Mustang9668 View Post
Do you have the gen 1 or gen 2 JLT?

Sent from my XT1080 using Tapatalk
I have no idea. When was the changeover?
__________________
03 Mach (Auto)
JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only)
mach1metalhead is offline   Reply With Quote
Old 04-22-2014, 01:26 PM   #15
Mustang9668
saving pennies
 
Mustang9668's Avatar
 
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
Re: Does any know if 2nd Gen. JLT CAI fits....

Quote:
Originally Posted by mach1metalhead View Post
I have no idea. When was the changeover?
Gen 1



Gen 2



Prob about 2 years ago. You can see the difference in the shield around the filter and the shape of the pipe.
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels

03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs
Mustang9668 is offline   Reply With Quote
Old 04-22-2014, 07:47 PM   #16
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
2nd generation intake tube looks not as wide and shorter than 1st, and looks like a longer filter. Remember that the 1st would hit the inside of hood. And now 2nd from what I read above clears Steed 2 point shock tower strut.

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-23-2014, 10:56 AM   #17
mach1metalhead
Registered User
 
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
Based on those pics, I have a Gen. 1. It clears my 2-pt brace, but it does rub the hood.
__________________
03 Mach (Auto)
JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only)
mach1metalhead is offline   Reply With Quote
Old 04-23-2014, 11:05 AM   #18
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by mach1metalhead View Post
Based on those pics, I have a Gen. 1. It clears my 2-pt brace, but it does rub the hood.
Not even the 45 degree fitting from throttle body?

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 04-24-2014, 01:48 AM   #19
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Quote:
Originally Posted by mach1metalhead View Post
Based on those pics, I have a Gen. 1. It clears my 2-pt brace, but it does rub the hood.
You don't happen to have a pic of it?

Sent from my SCH-I545 using Tapatalk
frijol79 is offline   Reply With Quote
Old 06-02-2014, 01:37 AM   #20
frijol79
Registered User
 
frijol79's Avatar
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 857
Re: Does any know if 2nd Gen. JLT CAI fits....

Wanted to update you guys that helped. It fits but tight fit with a bit of clearance issue but nothing serious.
frijol79 is offline   Reply With Quote
Old 06-02-2014, 11:17 AM   #21
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Does any know if 2nd Gen. JLT CAI fits....

Glad you got it,
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:39 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<