Who's Eaton Swapping Currently?? - Page 6 - 2003-04 Mach 1 Registry Owners Club

Mach828 · 06-10-2013, 03:02 PM

He told me 500 on the dot when it was still getting tuned. Not sure if he went higher than that or not.

Sent with a shot of DROID go fast

xMachYoux · 06-10-2013, 03:41 PM

Saw this beast yesterday... The swap came out good. Looks healthy!

SHAKN' 04 · 06-10-2013, 03:49 PM

11-12lbs of boost with the 3.1 pulley on e85? How much timing is in it?

watman02 · 06-10-2013, 10:41 PM

I want numbers!!!! and a dyno sheet would be nice too, with timing and AFR's...im not getting to the dyno anytime soon so i gota compare mine to the rest of u guys....I can tell ya from some playing around on thursday night i picked up a sec doing a logged pull at 7# at max of 16.75 timing at 11.7afr compared to 14* timing at 10.2afr at the same 7# of boost. pulls hard now!!!!

fastlane · 06-11-2013, 08:40 AM

Eaton Swap Dyno Graph by quikbluewagon, on Flickr

Here's mine, Eaton swapped with a 3.1" pulley, 96 Cobra cams, full exhaust, 10lbs of boost, 12.0 afr and 13 degrees of timing. The MAF was maxxed out so I need to get that straightened out before I go for more.

JaybTorchedMach · 06-11-2013, 10:18 PM

I don't remember the exact numbers but know that I ended on 500.26 RWHP. He has not emailed me the graphs yet but I will post them soon.

The first pull was about 497 RWHP on about 8 psi and timing spiked at almost 18 degrees, a little more than expected. We found that the boost actuator was not adjusted correctly and was bleeding boost. After adjusting the the actuator and pulling about two degrees I achieved 500 RWHP on about 10 psi (this is normal for the altitude here).

Notable Mods include:

- e85
- Billetflow 3.1 pulley
- Accufab SBTB
- Kooks LT's
- Kooks X-pipe
- Magnapacks
- JLT RAI
- T56

watman02 · 06-12-2013, 08:17 AM

Quote:

Originally Posted by JaybTorchedMach

I don't remember the exact numbers but know that I ended on 500.26 RWHP. He has not emailed me the graphs yet but I will post them soon.

The first pull was about 497 RWHP on about 8 psi and timing spiked at almost 18 degrees, a little more than expected. We found that the boost actuator was not adjusted correctly and was bleeding boost. After adjusting the the actuator and pulling about two degrees I achieved 500 RWHP on about 10 psi (this is normal for the altitude here).

Notable Mods include:

- e85
- Billetflow 3.1 pulley
- Accufab SBTB
- Kooks LT's
- Kooks X-pipe
- Magnapacks
- JLT RAI
- T56

nice numbers i didn't realize the boost valve could be out of adjustment like that i should check mine Im only making 7#. nice numbers though how's it drive? its alot of fun.

SHAKN' 04 · 06-12-2013, 09:32 AM

What pulley are you using?

watman02 · 06-12-2013, 10:01 AM

3.65. maybe its the ported blower also. just a thought

SHAKN' 04 · 06-12-2013, 10:51 AM

Quote:

Originally Posted by watman02

3.65. maybe its the ported blower also. just a thought

Yea stock pulley with a ported blower isnt gonna benefit too much. Im running a 3.4 seeing 9.5lbs on 13* timing 510/487 but my cams arent degreed for the set up. But his numbers are good for his mods. Good job JayB

watman02 · 06-12-2013, 03:00 PM

ya I've been thinking about dropping a pulley size to a 3.4 and backing timing down.

JaybTorchedMach · 06-12-2013, 08:49 PM

Thanks Guys! I'm quite happy with the results. Time to start piecing an engine and Whipple

JaybTorchedMach · 06-12-2013, 09:29 PM

Ask and you shall receive

watman02 · 06-12-2013, 09:32 PM

man the table top torque curves of eatons are awsome!!!!
good job JaybTorchedMach what timing are you running...16? and what are your AFR's?

JaybTorchedMach · 06-12-2013, 09:49 PM

Yes indeed, gotta love torque. The only thing with better torque is a twin screw! Timing is at 16ish. Keep in mind AFR is for e85. The lean at 4500 was fixed but has not been loaded since my programmer took a shiz.

bleedingfordblu · 06-29-2013, 02:31 PM

mine finally got tuned!

it put down 429 hp and 407 tq 16 degrees of timing, 7.5 lbs of boost stock pulley.

JaybTorchedMach · 06-30-2013, 05:38 PM

Quote:

Originally Posted by bleedingfordblu

mine finally got tuned!

it put down 429 hp and 407 tq 16 degrees of timing, 7.5 lbs of boost stock pulley.

Congrats! It's an amazing feeling having her back on the street

bleedingfordblu · 06-30-2013, 06:05 PM

yeah its nice! so happy

NativePony · 07-02-2013, 12:25 PM

Quote:

Originally Posted by bleedingfordblu

mine finally got tuned!

it put down 429 hp and 407 tq 16 degrees of timing, 7.5 lbs of boost stock pulley.

Congrats, ours put down very similar numbers on the stock pulley!!!

bleedingfordblu · 07-07-2013, 09:27 PM

haha yeah i saw the vids on youtube! thats all i watched when i was waiting for mine

32vAB · 07-15-2013, 11:56 AM

just finished my swap, going for a tune next month hopefully after a lower pulley upgrade (running a 2.76 upper now) to see what she makes!

Before/After

Mach828 · 07-15-2013, 12:26 PM

Quote:

Originally Posted by 32vAB

just finished my swap, going for a tune next month hopefully after a lower pulley upgrade (running a 2.76 upper now) to see what she makes!

Before/After

Why did you ditch the Vortech for the Eaton?

JaybTorchedMach · 07-15-2013, 10:03 PM

Nice build 32vAB! Any engine work.

I expect a build thread soon Mach828!

32vAB · 07-18-2013, 01:53 AM

Quote:

Originally Posted by Mach828

Why did you ditch the Vortech for the Eaton?

It was a Procharger.....and I've always wanted to do an Eaton swap on my car. Might have sacrificed some top end hp going to the Eaton but i'm more satisfied with it

Quote:

Originally Posted by JaybTorchedMach

Nice build 32vAB! Any engine work.

I expect a build thread soon Mach828!

Fully built engine:
5.0 stroker assembly (Kellogg crank, manley rods, dss pistons)
9.5:1 compression
all ARP
Comp stage 2 cams, BTR springs
Ported Eaton, 2.76 upper/stock lower (6# lower soon)
etc..etc.....

OWmach1 · 07-19-2013, 03:10 AM

Quote:

Originally Posted by Pcmoore85

Here is some pics of the custom brackets

looks good, but where does the p/s reservoir bolt up too?

06-10-2013, 03:02 PM	#126
Mach828 Dark Knight Join Date: Nov 2009 Location: Albuquerque, NM Posts: 5,759	He told me 500 on the dot when it was still getting tuned. Not sure if he went higher than that or not. Sent with a shot of DROID go fast __________________ Vortech V2 S-trim, E85, A2A Treadstone, Comp cams, built engine, full exhaust, built rear, built 4r70, more mods. Tuned by me with SCT Advantage

06-10-2013, 03:49 PM	#128
SHAKN' 04 Registered User Join Date: Jan 2008 Location: Kyle, Texas Posts: 2,285	Re: Who's Eaton Swapping Currently?? 11-12lbs of boost with the 3.1 pulley on e85? How much timing is in it? __________________ SOLD04' Mach 1 -Comp Cams 106100's (deg 106/110) -Eatonswap with 3.4 Pulley -Full Exhaust (mac lts & xpipe, sss terminator c/b) -Built Rear w/ 3.55 gears [B]-Tuned by Lethal Performance of San Antonio -510hp/478tq

06-10-2013, 10:41 PM	#129
watman02 Registered User Join Date: Aug 2009 Location: Denver, Ia Posts: 443	Re: Who's Eaton Swapping Currently?? I want numbers!!!! and a dyno sheet would be nice too, with timing and AFR's...im not getting to the dyno anytime soon so i gota compare mine to the rest of u guys....I can tell ya from some playing around on thursday night i picked up a sec doing a logged pull at 7# at max of 16.75 timing at 11.7afr compared to 14* timing at 10.2afr at the same 7# of boost. pulls hard now!!!! __________________ mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111 Last edited by watman02; 06-11-2013 at 02:38 PM.

06-11-2013, 08:40 AM	#130
fastlane Registered User Join Date: Mar 2011 Location: Fort Worth, TX Posts: 209	Re: Who's Eaton Swapping Currently?? Eaton Swap Dyno Graph by quikbluewagon, on Flickr Here's mine, Eaton swapped with a 3.1" pulley, 96 Cobra cams, full exhaust, 10lbs of boost, 12.0 afr and 13 degrees of timing. The MAF was maxxed out so I need to get that straightened out before I go for more.

06-11-2013, 10:18 PM	#131
JaybTorchedMach Registered User Join Date: Mar 2010 Location: Albuquerque, NM Posts: 1,746	Re: Who's Eaton Swapping Currently?? I don't remember the exact numbers but know that I ended on 500.26 RWHP. He has not emailed me the graphs yet but I will post them soon. The first pull was about 497 RWHP on about 8 psi and timing spiked at almost 18 degrees, a little more than expected. We found that the boost actuator was not adjusted correctly and was bleeding boost. After adjusting the the actuator and pulling about two degrees I achieved 500 RWHP on about 10 psi (this is normal for the altitude here). Notable Mods include: - e85 - Billetflow 3.1 pulley - Accufab SBTB - Kooks LT's - Kooks X-pipe - Magnapacks - JLT RAI - T56

06-10-2013, 03:41 PM	#127
xMachYoux Registered User Join Date: Feb 2013 Location: Albuquerque, New Mexico Posts: 82	Saw this beast yesterday... The swap came out good. Looks healthy!

06-12-2013, 09:32 AM	#133
SHAKN' 04 Registered User Join Date: Jan 2008 Location: Kyle, Texas Posts: 2,285	Re: Who's Eaton Swapping Currently?? What pulley are you using? __________________ SOLD04' Mach 1 -Comp Cams 106100's (deg 106/110) -Eatonswap with 3.4 Pulley -Full Exhaust (mac lts & xpipe, sss terminator c/b) -Built Rear w/ 3.55 gears [B]-Tuned by Lethal Performance of San Antonio -510hp/478tq

06-12-2013, 10:01 AM	#134
watman02 Registered User Join Date: Aug 2009 Location: Denver, Ia Posts: 443	Re: Who's Eaton Swapping Currently?? 3.65. maybe its the ported blower also. just a thought __________________ mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111

06-12-2013, 03:00 PM	#136
watman02 Registered User Join Date: Aug 2009 Location: Denver, Ia Posts: 443	Re: Who's Eaton Swapping Currently?? ya I've been thinking about dropping a pulley size to a 3.4 and backing timing down. __________________ mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111

06-12-2013, 08:49 PM	#137
JaybTorchedMach Registered User Join Date: Mar 2010 Location: Albuquerque, NM Posts: 1,746	Re: Who's Eaton Swapping Currently?? Thanks Guys! I'm quite happy with the results. Time to start piecing an engine and Whipple

06-12-2013, 09:29 PM	#138
JaybTorchedMach Registered User Join Date: Mar 2010 Location: Albuquerque, NM Posts: 1,746	Re: Who's Eaton Swapping Currently?? Ask and you shall receive

06-12-2013, 09:32 PM	#139
watman02 Registered User Join Date: Aug 2009 Location: Denver, Ia Posts: 443	Re: Who's Eaton Swapping Currently?? man the table top torque curves of eatons are awsome!!!! good job JaybTorchedMach what timing are you running...16? and what are your AFR's? __________________ mods:cai, flowmaster 40's, o/r x tune best et: 13.17@107mph & 8.56@84.5 1/8 new mods: spacer, 98 cobra cams 4.10's new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76 New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets TUNED by ME!....with SCT proracer softwear!! 482hp / 481tq new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4 00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune times: 1.8 60' 12.8 @111

06-12-2013, 09:49 PM	#140
JaybTorchedMach Registered User Join Date: Mar 2010 Location: Albuquerque, NM Posts: 1,746	Re: Who's Eaton Swapping Currently?? Yes indeed, gotta love torque. The only thing with better torque is a twin screw! Timing is at 16ish. Keep in mind AFR is for e85. The lean at 4500 was fixed but has not been loaded since my programmer took a shiz.

06-29-2013, 02:31 PM	#141
bleedingfordblu Registered User Join Date: May 2007 Location: Leesburg, VA Posts: 1,985	Re: Who's Eaton Swapping Currently?? mine finally got tuned! it put down 429 hp and 407 tq 16 degrees of timing, 7.5 lbs of boost stock pulley. __________________ 2003 Azure Blue Mach 1 Stock bottom end/compression Eaton M112 Stock upper Stock lower K&N intake Built T56 Bassani mid length headers Bassani catted x pipe Bassani slash cut tip catback Stock 03 Cobra IRS 18x9/10 Forgestar F14 Tuned by Chris Macduff at IMA motorsports 429hp 407 tq @ 7.5 lbs of boost

06-30-2013, 06:05 PM	#143
bleedingfordblu Registered User Join Date: May 2007 Location: Leesburg, VA Posts: 1,985	Re: Who's Eaton Swapping Currently?? yeah its nice! so happy __________________ 2003 Azure Blue Mach 1 Stock bottom end/compression Eaton M112 Stock upper Stock lower K&N intake Built T56 Bassani mid length headers Bassani catted x pipe Bassani slash cut tip catback Stock 03 Cobra IRS 18x9/10 Forgestar F14 Tuned by Chris Macduff at IMA motorsports 429hp 407 tq @ 7.5 lbs of boost

07-07-2013, 09:27 PM	#145
bleedingfordblu Registered User Join Date: May 2007 Location: Leesburg, VA Posts: 1,985	Re: Who's Eaton Swapping Currently?? haha yeah i saw the vids on youtube! thats all i watched when i was waiting for mine __________________ 2003 Azure Blue Mach 1 Stock bottom end/compression Eaton M112 Stock upper Stock lower K&N intake Built T56 Bassani mid length headers Bassani catted x pipe Bassani slash cut tip catback Stock 03 Cobra IRS 18x9/10 Forgestar F14 Tuned by Chris Macduff at IMA motorsports 429hp 407 tq @ 7.5 lbs of boost

07-15-2013, 11:56 AM	#146
32vAB Certified Join Date: Oct 2010 Location: Irvine, Ky Posts: 531	Re: Who's Eaton Swapping Currently?? just finished my swap, going for a tune next month hopefully after a lower pulley upgrade (running a 2.76 upper now) to see what she makes! Before/After Attached Thumbnails __________________ 03 Mach 1, 5.0, Comp Cams, Eaton, 2.76 pulley 02 SuperDuty King Cab 4x4 Home of the Modified Stage 2 FPDM! http://www.ebay.com/itm/121148784860...84.m1555.l2649

07-15-2013, 10:03 PM	#148
JaybTorchedMach Registered User Join Date: Mar 2010 Location: Albuquerque, NM Posts: 1,746	Re: Who's Eaton Swapping Currently?? Nice build 32vAB! Any engine work. I expect a build thread soon Mach828!

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)