|
|
Technical Q&A. HOW TO's, TSB's & Warranty Items Have a Problem? Technical Questions & Answers. HOW TO's & TSB's, Warranty Issues |
|
Thread Tools | Display Modes |
06-26-2005, 12:20 PM | #1 |
2004 DSG MACH 1 SALLEE
Join Date: Jun 2005
Location: Greencastle,PA
Posts: 203
|
Shaker noise
When i start my MACH up and its sitting there idioling a rattle noise comes from my shaker. I put 1 finger on it and it stops,i take it off and it starts. ANY clues to make it stop?
__________________
SOLD K&N Filter 4:10 FFRP Gears Superchips Handheld Tuner FRPP ADS NGK Plugs SLP LoudMouth 1 1" Shaker extension MGW Orange Shifter MRT StreetSmart CAI Steeda 2-point strut tower brace BASSANI CATTED X-PIPE 17x9 & 17x10.5 DD Blk Bullitt Wheels http://www.cardomain.com/ride/1985108 |
06-26-2005, 12:25 PM | #2 |
LuLz
Join Date: Dec 2003
Location: Cedar Park, TX
Posts: 19,294
|
Re: Shaker noise
theres a tsb for it, check the first thread in this forum labeled TSB's its on the first post
__________________
11 Sterling gray GT500 coupe 08 Silver Z06 1058rwhp/1073rwt @ 15psi 14 Silver Q50S Vortech blown 04 DSG Mach 1 (stolen) 03 OW Mach 1 (sitting in a field rotting away) |
06-26-2005, 01:07 PM | #3 | |
Administrator
Join Date: Jun 2005
Posts: 139
|
Re: Shaker noise
Quote:
• BODY—NOISE—HOOD SCOOP (SHAKER) RATTLE Article No. NOISE 03-22-1 • ENGINE—NOISE—HOOD SCOOP (SHAKER) RATTLE NOISE • NOISE—HOOD SCOOP (SHAKER) RATTLE NOISE FORD: 2003-2004 MUSTANG NOTE ISSUE USING A SCREWDRIVER TO HELP GUIDE THE Some 2003-2004 Mustang Mach 1 may exhibit a EDGE OF THE ISOLATOR INTO THE HOLE MAY rattle type noise from the Hood Scoop (Shaker) DAMAGE THE MATERIAL OF THE ISOLATOR. area. The noise may occur at any engine RPM and/or during acceleration or deceleration. 5. Once the entire outer edge is within the hole, push the isolator down into the hole. ACTION To service, install revised Hood Scoop Isolators 6. Reinstall the Hood Scoop. (four), part number (2L7Z-9P686-AA). Refer to the 7. Verify the condition is corrected. following Service Procedure. SERVICE PROCEDURE PART NUMBER PART NAME 2L7Z-9P686-AA Isolator 1. Remove the Hood Scoop per the Workshop Manual (Section 303-12). OTHER APPLICABLE ARTICLES: NONE 2. Place the Hood Scoop upside down on the WARRANTY STATUS: Eligible Under Provisions Of workbench. New Vehicle Limited Warranty Coverage NOTE OPERATION DESCRIPTION TIME PLACE HOOD SCOOP ON A CLOTH TO 032201A Install Revised Hood 0.7 Hr. PREVENT SCRATCHING OR MARRING OF THE Scoop Isolators (Includes FINISH. Time To Remove And Install Hood Scoop) 3. Remove the four (4) isolators by grasping with your fingers and pulling up and towards the center of the isolator (Figure 1). 4. Install new Isolators (2L7Z-9P686-AA) by setting the isolator in the hole at an angle (Figure 2) and pressing down, while working the outer edge of the isolator down into the hole with your fingers. NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Copyright ã 2003 Ford Motor Company PAGE 1 Article No. 03-22-1 Cont’d. DEALER CODING CONDITION BASIC PART NO. CODE 6N079 07 Figure 1 - Article 03-22-1 Figure 2 - Article 03-22-1 PAGE 2 |
|
06-26-2005, 02:13 PM | #4 |
2004 DSG MACH 1 SALLEE
Join Date: Jun 2005
Location: Greencastle,PA
Posts: 203
|
Re: Shaker noise
Yup it sure did guys Thanks again!!!
__________________
SOLD K&N Filter 4:10 FFRP Gears Superchips Handheld Tuner FRPP ADS NGK Plugs SLP LoudMouth 1 1" Shaker extension MGW Orange Shifter MRT StreetSmart CAI Steeda 2-point strut tower brace BASSANI CATTED X-PIPE 17x9 & 17x10.5 DD Blk Bullitt Wheels http://www.cardomain.com/ride/1985108 |
06-26-2005, 02:15 PM | #5 | |
Administrator
Join Date: Jun 2005
Posts: 139
|
Re: Shaker noise
Quote:
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|