Forum: 2003-04 Mach 1 - For Sale/Wanted
11-22-2010, 08:51 PM
|
Replies: 9
Views: 1,059
|
Forum: 2003-04 Mach 1 - For Sale/Wanted
11-22-2010, 09:33 AM
|
Replies: 1
Views: 1,213
Twin turbo mach for sale
Due to unforeseen circumstances I have to sell my Mach 1 this car has all the best parts in it and makes great power. I hate to sell if after getting it finally completed. I am asking 25k for the car...
|
Forum: Power Adders
11-02-2010, 11:46 AM
|
Replies: 50
Views: 52,387
Re: Official Turbo HP/TQ Thread
Turbo Manfacturer: Garrett twin 57's
Single or Twin or Hellraiser: twin
A/R Type:
Stock or Modified Cold Side Piping:modified
Stock or Modified Downpipe:modified
Heads: stock hand ported ...
|
Forum: Power Adders
10-28-2010, 07:17 AM
|
Replies: 20
Views: 1,475
|
Forum: Power Adders
10-27-2010, 02:06 PM
|
Replies: 20
Views: 1,475
|
Forum: Power Adders
10-27-2010, 11:04 AM
|
Replies: 20
Views: 1,475
Re: Dyno #'s for the new setup
yea when I had the blower it took me 22 to make that kind of power plus the turbo's are a lot more streetable. It is just so nice to get 14 mpg making that kind of power.
|
Forum: Power Adders
10-26-2010, 09:08 AM
|
Replies: 20
Views: 1,475
Re: Dyno #'s for the new setup
I had issues with alum block that was in the car that is the only reason i changed the block.
Right now I am only running 13 lbs of boost
|
Forum: Power Adders
10-25-2010, 01:15 PM
|
Replies: 20
Views: 1,475
|
Forum: Power Adders
10-25-2010, 11:08 AM
|
Replies: 20
Views: 1,475
Re: Dyno #'s for the new setup
Yea there are a few $$$$ in it LOL
THe motor is built it has manley billet rods, cp piston, and all the other little goodies that go with it.
should be capable of over a 1000 rwhp with race...
|
Forum: Power Adders
10-25-2010, 08:03 AM
|
Replies: 20
Views: 1,475
Dyno #'s for the new setup
The new setup is twin 57mm turbo's my custom avaitor intake and custom grind cams to maximize the turbo's. finally got the tune cleaned up on friday Here is the video of the run and my final #'s...
|
Forum: 2003-04 Mach 1 - For Sale/Wanted
04-28-2010, 09:07 AM
|
Replies: 7
Views: 1,992
Re: Built 2004 Torch red mach 1 in nc for sale
Right now with 8 lbs of boost and only turning it to 5800 rpm it is at 647 rwhp we are still putting break in miles on the motor. the short block is capable of 1000 + and I am expecting over 800 on...
|
Forum: 2003-04 Mach 1 - For Sale/Wanted
04-27-2010, 12:37 PM
|
Replies: 2
Views: 563
Re: WTB MACH1 in NJ area
This car has been built with all the best parts I am going to sacrifice it for $22500. Here is a list of everything that has been installed on the car
Its a little travel but well worth it
...
|
Forum: 2003-04 Mach 1 - For Sale/Wanted
04-05-2010, 02:03 PM
|
Replies: 7
Views: 1,992
|
Forum: 2003-04 Mach 1 - For Sale/Wanted
04-01-2010, 07:17 AM
|
Replies: 7
Views: 1,992
|
Forum: 2003-04 Mach 1 - For Sale/Wanted
03-18-2010, 01:44 PM
|
Replies: 7
Views: 1,992
Built 2004 Torch red mach 1 in nc for sale
unforunatly I have to sell this car due to unforeseen moving expense's.
This car has been built with all the best parts I am going to sacrifice it for $25000. Here is a list of everything that...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
08-12-2006, 10:22 AM
|
Replies: 87
Views: 3,696
|
Forum: Engine & Drivetrain (Including trans & rear axles)
08-12-2006, 09:58 AM
|
Replies: 87
Views: 3,696
Re: Almost 700 RWHP on Pump gas
Well I just want to get 800 to the rear wheels that is the goal anyways we are not to far away I think a boost a spark and we will be able to do it. then I'm done with this one. I'm thinking of...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
08-11-2006, 07:58 PM
|
Replies: 87
Views: 3,696
|
Forum: Engine & Drivetrain (Including trans & rear axles)
08-10-2006, 09:16 PM
|
Replies: 87
Views: 3,696
Re: Almost 700 RWHP on Pump gas
Right now it is the stock 3650, everything else has been upgraded I put a detroit locker in a week or so ago and changed the gear ratio to 3:90's and 31 spline mosher axels the tranny is the last...
|
Forum: US-SouthEast Region
08-10-2006, 09:14 PM
|
Replies: 56
Views: 3,447
Re: Mach 1 Dyno Day in Raleigh
Well the heads are stock mach 1 heads ported by randy haywood at haywood custom speed in raleigh it takes a while to get them done but it is well worth the wait
|