|
|
Mustangs Parts For Sale/Wanted Looking for a Mustang or Part or have one for sale? Post it here! |
|
Thread Tools | Display Modes |
07-02-2008, 09:38 PM | #1 |
Registered User
Join Date: Jun 2004
Location: Chesapeake, Virginia
Posts: 734
|
2003-04 Mustang Tremec 3650 Wanted
Hello I have a friend interested in buying a 2003-2004 Ford Mustang Mach 1/ GT Tremec 3650 transmission that has no problems. If anyone has one in like new working condition let me know. Send the information and price in a private message or post.
|
07-02-2008, 10:36 PM | #2 |
MarinesMach1
Join Date: Dec 2006
Location: Denham Springs,LA
Posts: 467
|
Re: 2003-04 Mustang Tremec 3650 Wanted
__________________
P1SC/3.4 pulley,60# injectors, Comp stage 2 blower cams,Cp pistons, Probe rods Beehive valve springs,AFM power pipe,SLP line lock,Cobra tank and pumps,BBK long tubes, o/r x,Magnapacks,T56-26 spline input shaft, MGW shifter,Centerforce DFX, Steeda springs,Steeda H/D UCA's,Metco LCA's,Eaton posi,3.73's,Moser 31 splines, Black 18" FR500's 295/35 BFG drag radials. |
07-03-2008, 12:13 AM | #3 |
Registered User
Join Date: Dec 2005
Location: Herndon, VA
Posts: 541
|
Re: 2003-04 Mustang Tremec 3650 Wanted
Should be a very easy find on here, i've seen a lot for sale recently. Good luck
__________________
2004 Torch Red Mach 1! Eaton Swapped 8psi SLP Longtube Headers SLP Catted Shorty X SLP Powerflo Catback JLT RAI Intake SCT Tune on 4bank chip Nitto DR 275/40/17 MM Lower Control Arms MM Urethane Rack Bushings Hawk HPS Pads w/ MM brake lines MM Full Length Subframes Steeda Tri-ax Sirius For Sale! |
07-03-2008, 02:13 PM | #4 |
Registered User
Join Date: Nov 2007
Location: Dublin, Georgia
Posts: 259
|
Re: 2003-04 Mustang Tremec 3650 Wanted
I will have mine available in about 2 weeks if you haven't found one by then.
Eric
__________________
Eric 2003 Black 03 Mach 1 T56-swap, built rearend, full bolt ons. 321/342 .... next up: ported heads, GT cams, build bottom end, fuel system, then D1SC. |
07-03-2008, 02:21 PM | #5 |
Girls Drag Race in Heels
Join Date: Jan 2008
Location: Pembroke, NC
Posts: 531
|
Re: 2003-04 Mustang Tremec 3650 Wanted
ls1 Killer has one
__________________
Cheryl's 2004 Mach 1 Eaton Swapped Stock Pulley,8lbs of boost: 431/406 Conservative Tune 2.9 Pulley, 11 lbs of boost: 487/490 Conservative Tune Installed and Tuned by Fastlane Motorsports Exhaust: Bassani offroad x, Bassani Midlength Headers, Flowmaster Catback, JLT Fenderwell Cold Air Intake, 4:10 Gears, Caster Camber Plates, Steeda Sport Springs, 17x9/17x10.5 Chrome Bullitt Rims |
07-03-2008, 08:46 PM | #6 | |
Registered User
Join Date: Jan 2006
Location: here,here
Posts: 592
|
Re: 2003-04 Mustang Tremec 3650 Wanted
Quote:
|
|
07-03-2008, 10:29 PM | #7 |
MarinesMach1
Join Date: Dec 2006
Location: Denham Springs,LA
Posts: 467
|
Re: 2003-04 Mustang Tremec 3650 Wanted
Not a problem buddy, and hes even close by so shipping wont be too bad.
__________________
P1SC/3.4 pulley,60# injectors, Comp stage 2 blower cams,Cp pistons, Probe rods Beehive valve springs,AFM power pipe,SLP line lock,Cobra tank and pumps,BBK long tubes, o/r x,Magnapacks,T56-26 spline input shaft, MGW shifter,Centerforce DFX, Steeda springs,Steeda H/D UCA's,Metco LCA's,Eaton posi,3.73's,Moser 31 splines, Black 18" FR500's 295/35 BFG drag radials. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|