|
|
Mustangs Parts For Sale/Wanted Looking for a Mustang or Part or have one for sale? Post it here! |
|
Thread Tools | Display Modes |
08-13-2013, 08:45 PM | #1 |
Registered User
Join Date: Nov 2003
Location: Schertz, TX
Posts: 2,639
|
swapping in a 5.0 coyote, selling off my parts
I had my almost to the 9s (acutally could have been there if I hadn't had it slightly de-tuned to prevent the need for a cage and license). Then my fuse blew to my electric water pump and I missed it until it got really hot. Now I'm in need of an engine rebuild.
So....I'm going to go with a NMRA coyote stock engine. That class has looked interesting for a while and my car is almost set up almost exactly for it. I'm ordering the motor tomorrow. I'm going to be parting out the procharger D1SC , intercooler, heads with comp cams, electric water pump, SLP long tubes and just about everything related to the old motor except for the short block which needs work. I will probably sell the stroker crank and ATI balancer as well. and maybe the rods (these are acutally chevy h-beam rods since it was a long rod stroker) A bunch of extra parts such as an underdrive ATI balancer and extra elec water pump without the pulley (new in box) will be going also. I'll try to compile a list soon and put it on the for sale board. The new setup should be at least in the high tens. I'll need mid 10s to be competitive. I expect to need a gear change so my 3.73s will probably also be on their way out too.
__________________
Zinc yellow NMRA Factory Stock configuration Coyote 5.0 engine, FRPP Control Pack and a bunch of other stuff. Best ET in this configuration 10.693@123 |
08-13-2013, 08:52 PM | #2 |
Registered User
Join Date: Aug 2011
Location: Helotes, TX
Posts: 179
|
Re: swapping in a 5.0 coyote, selling off my parts
How much for the cams? Or heads/cam combo?
|
08-13-2013, 09:40 PM | #3 |
Original 03 TR Owner
Join Date: Apr 2004
Location: Waco, TX
Posts: 2,860
|
Re: swapping in a 5.0 coyote, selling off my parts
See ya' at the Shootout!
Keep us posted........... Big Ron |
08-13-2013, 09:41 PM | #4 |
Registered User
Join Date: Apr 2013
Location: Lexington Park, Maryland
Posts: 77
|
Re: swapping in a 5.0 coyote, selling off my parts
Very similar to my setup that I have for sale. I'm doing a swap also!
GLWS.
__________________
Old username: 04azuremach. The account is locked from inactivity and Dave hasn't responded to my e-mails about reactivating it, so here I am. Old setup: DSS 5.0 stroker, C4 Trans, Aeromotive fuel, Paxton NOVI 2000 768 rwhp/588 rwtq. 9.960 @ 135 1/4 (with 649 rwhp) New setup: Built 408 (6.7 liter) LSX, TH400, Aeromotive fuel. Numbers to come eventually. Cogged YSi and 8 second slips to come in the distant future |
08-13-2013, 10:34 PM | #5 |
Registered User
Join Date: Nov 2003
Location: Schertz, TX
Posts: 2,639
|
Re: swapping in a 5.0 coyote, selling off my parts
Not sure yet. I've got to get an inventory and see if the shop checked to see if the heads need to be trued up or not. I'll post up soon.
__________________
Zinc yellow NMRA Factory Stock configuration Coyote 5.0 engine, FRPP Control Pack and a bunch of other stuff. Best ET in this configuration 10.693@123 |
08-13-2013, 11:24 PM | #6 |
Registered User
Join Date: Jul 2008
Location: Texas
Posts: 906
|
Re: swapping in a 5.0 coyote, selling off my parts
GLWS cant wait to see the results of the swap, do you have any vids of your car running on d1 setup?
__________________
JLT, xpipe, tune and the Darrinmatic and a lil bit of Sauce tuned by Lethal Performance in San Antonio TX |
08-14-2013, 09:44 AM | #7 | |
Registered User
Join Date: Nov 2003
Location: Schertz, TX
Posts: 2,639
|
Re: swapping in a 5.0 coyote, selling off my parts
Quote:
http://0e7408a37c3c5d33968e-55110697...n.com/car.mpeg EDIT: I tried that video and could only see the burnout. Here's a .mov version of it. http://0e7408a37c3c5d33968e-55110697...R_03.01.13.MOV
__________________
Zinc yellow NMRA Factory Stock configuration Coyote 5.0 engine, FRPP Control Pack and a bunch of other stuff. Best ET in this configuration 10.693@123 |
|
08-14-2013, 11:09 PM | #8 | |
Registered User
Join Date: Jul 2008
Location: Texas
Posts: 906
|
Re: swapping in a 5.0 coyote, selling off my parts
Quote:
cool thanks!!
__________________
JLT, xpipe, tune and the Darrinmatic and a lil bit of Sauce tuned by Lethal Performance in San Antonio TX |
|
08-18-2013, 03:01 PM | #9 |
2v 04 cobra?
Join Date: May 2012
Location: miami, fl
Posts: 206
|
Re: swapping in a 5.0 coyote, selling off my parts
would a 03-04 t56 work with this engine because for a while ive been looking into these steps as well
__________________
Daily: Azure blue Auto Mach 1 305 RWHP, 325 RWTQ Race Car: 04 2V Cobra <---- yes a 2v 520 RWHP, 680 RWTQ Built lightning motor on low boost |
08-18-2013, 04:24 PM | #10 |
Registered User
Join Date: Dec 2008
Location: evansville indiana
Posts: 389
|
Re: swapping in a 5.0 coyote, selling off my parts
Yep. Any 4.6 trans will mate to it.
__________________
2004 DSG Mach 1 - 11.79 1/4 (7.48 1/8) 1994 Cobra (terminator swap) -10.44 1/4 |
08-19-2013, 02:14 PM | #11 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: swapping in a 5.0 coyote, selling off my parts
the problem with doing this swap on a street car is getting the dash to work. To do that you need to run two computers, one for the engine and the other to send the signals to the dash.
__________________
https://www.facebook.com/groups/481330828691064/ |
08-20-2013, 01:44 AM | #12 |
AUTOMACHTIC
Join Date: Oct 2007
Location: RTP/ N.C.
Posts: 4,813
|
Re: swapping in a 5.0 coyote, selling off my parts
There is also no option to run an automatic trans with this motor from Ford
__________________
UPGRADES...Tokico Illuminas Borla SS Catback , Steeda Underdrives , Strut Brace , HPM Lower K Brace , L /C Arms , U /C Arms , HPM PanHard Bar, K&N FRPK 2, GOODYEAR GT1 , MRT- H-Pipe , JLT VaporTraps , SLP-12'" Tips! , FRPP Shorty 1 5/8 Headers , Brembo D/S & PBR D/S Rotors ,FRPP Alum.DS ,Roys 3/8 Spacer , SVT Focus 255 pump SCTsw Chip PRO-DYNOjet NA 300.01hp /315tq (Auto) ,Innovate W/B ,Compucar Wet Kit (90jet) + Heater and E Gauge * 360 hp/385tq 12.5 -1/4 @112 |
08-20-2013, 04:29 AM | #13 |
"God of Thunder"
Join Date: Jan 2007
Location: DC
Posts: 1,076
|
Re: swapping in a 5.0 coyote, selling off my parts
How many bones did you give for the Coyote Motor, if you don't mind sharing such information?
|
08-20-2013, 09:56 AM | #14 | |
Registered User
Join Date: Nov 2003
Location: Schertz, TX
Posts: 2,639
|
Re: swapping in a 5.0 coyote, selling off my parts
Quote:
Plus headers, balancer, etc.
__________________
Zinc yellow NMRA Factory Stock configuration Coyote 5.0 engine, FRPP Control Pack and a bunch of other stuff. Best ET in this configuration 10.693@123 |
|
08-20-2013, 09:57 AM | #15 |
Registered User
Join Date: Nov 2003
Location: Schertz, TX
Posts: 2,639
|
Re: swapping in a 5.0 coyote, selling off my parts
If you use a 4.6L automatic computer you could run any trans that mates to 4.6 and is supported by that computer. If you use the Ford Racing ECU that's referenced on the web page, you would need a manual trans like a C4 with a proper bellhousing for a mod motor.
__________________
Zinc yellow NMRA Factory Stock configuration Coyote 5.0 engine, FRPP Control Pack and a bunch of other stuff. Best ET in this configuration 10.693@123 |
08-24-2013, 05:00 PM | #16 |
Registered User
Join Date: Mar 2013
Location: Fall River, Ma.
Posts: 37
|
Re: swapping in a 5.0 coyote, selling off my parts
how much for the Procharger set up? Very interested. PM me please. I dont get on here often.
|
08-25-2013, 01:59 AM | #17 |
Registered User
Join Date: Nov 2012
Location: Fairfield,Ca
Posts: 143
|
Re: swapping in a 5.0 coyote, selling off my parts
How much for the slp longtubes text me with the pictures of your procharger kit also pls
8505257254 |
08-25-2013, 11:35 AM | #18 |
Registered User
Join Date: Dec 2008
Location: San Marcos, TX
Posts: 71
|
Re: swapping in a 5.0 coyote, selling off my parts
Sent PM on headers and heads a few days ago.
|
09-01-2013, 05:28 PM | #19 |
Registered User
Join Date: Jun 2006
Location: waller, tx
Posts: 1,225
|
Re: swapping in a 5.0 coyote, selling off my parts
Jaime, I'd be interested in the ProCharger setup. Just picked up an 04 in need of boost...
__________________
'07.5 Duramax. '12 Cruze. '03 Mach. 2x GT.
John Deere 790. Bunch of Arctic Cats in pieces. 2 kitchen sinks, and a Partridge in a pear tree. |
09-25-2013, 12:57 PM | #20 |
Registered User
Join Date: Sep 2008
Location: Brookhaven, Pa
Posts: 14
|
Re: swapping in a 5.0 coyote, selling off my parts
Also interested in the procharger..
__________________
JLT, SCT, SLP X, SLP LM, FRPP 4.10, H&R SS, MM CASTOR/CAMBER PLATE, STEEDA BUMP STEER, STEEDA X2 BALL JOINTS, TOKICO SHOCKS, AFS 17x9 & 17x10.5 |
09-26-2013, 05:07 PM | #21 |
Registered User
Join Date: Aug 2009
Location: evansville indiana
Posts: 38
|
Re: swapping in a 5.0 coyote, selling off my parts
pm'd you.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|