|
|
Mustangs Parts For Sale/Wanted Looking for a Mustang or Part or have one for sale? Post it here! |
|
Thread Tools | Display Modes |
10-16-2009, 08:30 PM | #1 |
semi-pro moderator
Join Date: May 2004
Location: Virginia Beach
Posts: 4,955
|
FS: SLP LT Headers and Catted X-pipe
********sold!*******
Here's what you get: SLP 1-5/8" Long Tubes: about 15k miles SLP Catted X-pipe: about 15k miles 3 O2 Extensions: 2 are new, 1 is used All new header bolts All the clamps for the cats to the mid pipe/collector The headers and x-pipe do have some scratches and one really small dent in one of the primaries. The headers are ceramic coated. I would recommend running a wire wheel around the slip-joints when you go to reassemble everything to make it easier. Of course they're dirty but nothing a little elbow grease can't fix. $500 Shipped to the lower 48. They are boxed up and ready to go.
__________________
2004 Mach 1 IUP/5spd/DSG Engine, etc done...sits in the garage Last edited by DTMach1; 11-12-2009 at 02:20 PM. |
10-16-2009, 09:52 PM | #2 |
Registered User
Join Date: Dec 2005
Location: Herndon, VA
Posts: 541
|
Re: FS: SLP LT Headers and Catted X-pipe
Nice deal right there! Good luck with the sale.
__________________
2004 Torch Red Mach 1! Eaton Swapped 8psi SLP Longtube Headers SLP Catted Shorty X SLP Powerflo Catback JLT RAI Intake SCT Tune on 4bank chip Nitto DR 275/40/17 MM Lower Control Arms MM Urethane Rack Bushings Hawk HPS Pads w/ MM brake lines MM Full Length Subframes Steeda Tri-ax Sirius For Sale! |
10-17-2009, 11:07 AM | #3 |
Registered User
Join Date: Mar 2008
Location: Cobb Island, MD
Posts: 587
|
Re: FS: SLP LT Headers and Catted X-pipe
PM sent
__________________
Full SLP, JLT, Diablo, 4.10s, DRs 1/8.......7.74 @ 90 1/4......12.09 @ 113.5 |
10-17-2009, 12:00 PM | #4 |
FOR SALE
Join Date: Jul 2008
Location: Bel Air, Maryland
Posts: 733
|
Re: FS: SLP LT Headers and Catted X-pipe
awesome deal there. im shocked your selling so low
bump and good luck with the sale
__________________
2004 Azure Blue Mach 1 with every bolt on-SOLD 2014 Mustang GT 5.0- Bone Stock... for now |
10-17-2009, 12:09 PM | #5 |
semi-pro moderator
Join Date: May 2004
Location: Virginia Beach
Posts: 4,955
|
Re: FS: SLP LT Headers and Catted X-pipe
All PMs replied too...I've got 3 people interested...
__________________
2004 Mach 1 IUP/5spd/DSG Engine, etc done...sits in the garage |
10-17-2009, 05:33 PM | #6 |
hunt'n for chevy's
Join Date: May 2006
Location: Southern CA
Posts: 660
|
Re: FS: SLP LT Headers and Catted X-pipe
im interested too.. i call uhh, 4th dibs (lol) if this other mid-pipe with cats doesnt go through...
might as well spend a $100 more and get headers with the deal! =D
__________________
2003 Torched Mach1, IUP, 5spd My Mach is for sale.. http://www.mach1registry.org/forums/...d.php?t=108311 2002 Trans Am WS6 M6. Sold but not forgotten |
10-21-2009, 08:54 PM | #7 |
semi-pro moderator
Join Date: May 2004
Location: Virginia Beach
Posts: 4,955
|
Re: FS: SLP LT Headers and Catted X-pipe
Sale is pending...I'll keep everyone informed one way or another!
__________________
2004 Mach 1 IUP/5spd/DSG Engine, etc done...sits in the garage |
11-12-2009, 02:19 PM | #8 |
semi-pro moderator
Join Date: May 2004
Location: Virginia Beach
Posts: 4,955
|
Re: FS: SLP LT Headers and Catted X-pipe
******SOLD!******
Thanks to Ryan, hope you like them! For everyone else, pay attention to my next couple of posts in the FS section...I've got some stuff that I'm sure someone wants
__________________
2004 Mach 1 IUP/5spd/DSG Engine, etc done...sits in the garage |
11-12-2009, 02:25 PM | #9 |
Registered User
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
|
Re: FS: SLP LT Headers and Catted X-pipe
|
11-12-2009, 02:34 PM | #10 |
semi-pro moderator
Join Date: May 2004
Location: Virginia Beach
Posts: 4,955
|
Re: FS: SLP LT Headers and Catted X-pipe
Probably nothing you need...but off the top of my head...FORE fuel rails for Mach1/01 Cobra (will not work with eaton), FR500 Cam kit (the whole kit), Stock Eaton S/C, NAZ ported intake with lid and spacer, Cobra fuel hat with stock pumps, Mach 1 front cover (the one I bought from you LOL), Fidanza alum fw with new insert, TKO 600, tr-3650, most of the 4v timing kit (mixed new/old parts), plus some more stuff that I have to find...I have a lot of stock parts that LookNGo has dibs on once I sort everything out.
__________________
2004 Mach 1 IUP/5spd/DSG Engine, etc done...sits in the garage |
11-12-2009, 05:13 PM | #11 |
allyourcamsbelong2me
Join Date: Jan 2008
Location: Houston,Texas
Posts: 784
|
Re: FS: SLP LT Headers and Catted X-pipe
How much you asking for the intake setup?
__________________
04 Redfire Mustang V6-T5-bolt ons and a gear-14.5@97 (SOLD...never forgotten) 03 DSG Mustang Mach 1-3650-IUP-(BUILD DATE-02/28/2003)-320RWHP 337RWTQ |
11-12-2009, 05:28 PM | #12 | |
Registered User
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
|
Re: FS: SLP LT Headers and Catted X-pipe
Quote:
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|